ALL

Nelson Bench Knock OFF {Tutorial}

Design + Build

Crafty Projects

Business + Life

Holidays

The Weekender Series

As Seen on TV

Room Makeovers

All DIY Projects

Search...

blog Categories

hey there! I'm monica 

I pride myself on making amazing style and design accessible for everyone, regardless of location, budget, or ability! My design philosophy is rooted in authenticity + attainability - If I can do it, you can too! My work has been featured in countless publications, but I take the most pride in homeowners that have been personally inspired by my DIY ideas and have tried something in their own homes!

learn more about ME + MY BIZ

Another amazing detail about these Knock Off projects, the DIY price! Becki & Chris of The UnCommon Common Law are showing off their 3rd place win that only cost them $136.52 compared to the original price of a Nelson Bench at $899…we said it was amazing, didn’t we?! If you missed our 2nd and first place knock off projects you are going to want to check them out here and here! Becki and Chris are coming to us from Canada, hey! She is a freelance graphic designer and photographer, and has been sharing the adventures of their DIY home renovations on their blog. We love their style and can’t wait to see what they do for round 2, take a look at their awesome tutorial and leave them some love.

——————————————————————————————————————————————————————

For those joining us late, we were selected as one of 12 contestants to compete in East Coast Creative Blog’s Creating With the Stars competition. The first round’s theme was create a DIY knock off of an existing product. We love the midcentury modern aesthetic, so we chose to recreate the infamous Nelson Platform Bench by iconic furniture company Herman Miller. This is the classic midcentury modern “slat bench” (which inspired our slat wall) and has been in production since 1946! We constructed our bench from 100% Canadian maple, with a total out of pocket cost of $136.52 (only had to purchase the lumber). Not a bad savings when compared to the original price of $899 plus shipping!

Img 3 800px

Materials:
7 – 1x2x8 maple lumber
2 – 1x3x6 maple lumber
1 1/4″ 18 g brad nails
1 3/4″ wood screws
Wood glue
1 can Varathane Satin Wood Finish
Minwax Pre-stain Wood Conditioner
Minwax Polyshades in Classic Black
Hammer-in felt furniture sliders
Wood filler
Sand paper

Tools:
Compound miter saw
Table saw with dado blade (or router table with 3/4″ dado bit) (or fine toothed backsaw, chisel and patience)
Air compressor and brad nailer (optional)
Belt sander (not require if your dados depth is exact)
Impact driver
Drill
Counter sink bit

IMG_7621

Planning was based on the specs found on the Herman Miller website. Interestingly, they provide 3D files of all their products which allowed us to pull angles and measurements directly from SketchUp! Note the slats in the original Nelson bench are actually a non-standard 5/8″ x 1 3/4″ – we opted to use standard 1x2s (which actually measure 3/4″ x 1 1/2″) to avoid having to rip down our own lumber, saving time and money. On a four foot bench, the slightly smaller lumber doesn’t alter stability.

Nelson Bench Sketchup

The first step was to cut 12 four foot slats from six of the 1x2x8s. They were actually a bit shy of four feet, as we cut a bit extra off the ends to make all the pieces equal in length.

IMG_7635

The seventh 1×2 was cut into four pieces to create the cross braces that hold the slats together. Note that even though the final length of the cross braces would be 17 1/4″ (the depth of the bench), the 1×2 was cut into four roughly equal 24″ pieces. The extra length on the ends was used to screw the pieces together. This allowed all the dado cuts to be made simultaneously, ensuring that all pieces were identical.

The next step, cutting the dado joints, is crucial. Really take the time to dial in the width and height of your blade to ensure a nice snug and flush fit. Your cut width should be identical to the width of the 1x2s you’re using and the height should be exactly half. Test the fit with scrap 1x2s.

Three-quarter inch dados were cut through the cross braces, 3/4″ deep and evenly spaced by 3/4″. To ensure uniform spacing, a jig was created and clamped to the mitre gauge (which can be pushed back and forth via the mitre slot in a consistent, repeatable manner). The jig was made by screwing a small cut end off a 1×2 (which matches the dado width of 3/4″) to a scrap piece of particle board to act as a spacer. This spacer was positioned exactly 3/4″ away from the nearest edge of the dado blade (this distance determined the size of the gap between dados).

IMG_7639

IMG_7642

The first dado was cut through the cross braces, and then that freshly cut dado was fit snugly over the 1×2 on the jig. Since the jig’s 1×2 block was precisely mounted 3/4″ away from the blade, everything automatically lined up for the second dado cut. This was repeated for a total of 12 dados, the cross brace repeatedly hopping over exactly 3/4″ between every cut. The screwed together ends of the cross braces were then cut off on the mitre saw, resulting in the final desired cross brace length of ~17 1/4″.

IMG_7644

Don’t have a table saw? This same technique can be used on a router table with a dado bit (I think I got my router table and router on sale as a bundled promotion for $99, and the bit should be fairly cheap depending on your source). Or you could reduce your carbon foot print and use a good old fashioned fine toothed backsaw and chisel like they did in 1955.

Dados in the twelve slats were cut in a similar manner, but only two cuts in the centre of each slat and one on each end were required. Cuts were made by clamping together four slats at a time. Note that the two centre dados were directly adjacent to one another, effectively making a 1 1/2″ wide dado to fit the doubled up centre cross brace.

IMG_7653

Once the pieces were all cut (and tested by dry fitting them together), the joints were glued and brad nailed from underneath. Nail holes were filled with wood filler. Alternatively, clamps could be used instead of brad nails to keep the joints held tight together while the glue dries. Once dry, the joints were sanded flush with a belt sander. The sharp edges were eased by hand with 80 grit sand paper and the whole bench was then hand sanded through multiple grits, up to 220.

IMG_7665

IMG_7673

IMG_7712

The legs of the bench consist of two trapezoid rings made from maple 1x3s. Since the bench top was scaled down slightly, we proportionally scaled down the dimensions of the legs. Angles were measured in Sketchup and confirmed by good old fashioned math. The angles we used were 98.6 and 81.4 degrees and the outer perimeter measurements of the trapezoid were as follows: top brace 16 3/4″, bottom brace 13 1/4″, both sides 12 1/8″ (see diagram below).

We mitered the joints because we’re anal (angles for the end of each piece therefore would be half of 98.6 or 81.4 degrees), but you don’t necessarily have to. All cuts were made on a compound mitre saw and the pieces were glued and screwed together (screwed from the top and bottom to ensure holes would be hidden). Countersunk pilot holes were drilled first to prevent wood splitting. The screw holes were concealed with wood filler and, once dry, the legs were sanded like the bench top.

IMG_7648

IMG_7701

IMG_7716

Before moving on to the final wood finishing, we screwed the legs to the bench (again, pre-drilling pilot holes to prevent splitting). We were also extremely careful to drill square with the slats, as the last thing we wanted was a drill bit popping out the side of the bench. We had to use our “close quarters” right angle drill to fit into the opening of the bases. A screw was placed in each slat. Before staining, the legs were removed; the purpose of mounting them first was to simply get all the holes pre drilled because it’s easier to fix any potential mistakes on raw wood than a finished wood product.

IMG_7729

As an aside, anytime you are working with wood stain, please please please don’t just jump in and try it on your project right away. Do a stain test on scrap wood. It will save you hours of swearing/sanding and if you try various products and techniques, you might be surprised which actually turns out looking the best.

The Herman Miller site says the wood legs are “ebonized”, which essentially is a fancy way of saying stained black. We used Minwax Polyshades in Classic Black. I’m usually weary of these “all in one” stain/clear coat products, but I found it covers a lot more even (more like a gel stain) and is a lot more opaque than a standard ebony stain we tried during our tests. Plus we had already used it on a project a while back with no issues. We applied a single coat of pre-stain wood conditioner first, waited 15 minutes and then applied the first coat of the black stain. Two additional coats were applied, waiting for the legs to completely dry (>8 hours) and lightly sanding with 220 grit paper between coats. The final finish wasn’t great (likely because it’s a combined all-in-one product) so we sprayed on a few light coats of satin Varathane to finish it off (see below). Note that these are all oil based products, not to be mixed with water based products.

IMG_7761

IMG_7767

IMG_7826

The bench top was left natural maple and finished with an oil based satin clear coat. In our opinion, one of the best kept secrets in woodworking is aerosol varnish. If you don’t own an HVLP gun/compressor or if your project is too small to justify the set up/clean up time of your HVLP gun (i.e. us being lazy), these cans are great. Perfect spray on finish with minimal setup/cleanup. You will need to still prep your work area though. Grab some plastic drop sheets and painter’s tape, find the most dust and clutter free room in the house and setup your spray booth/kill room. When spraying your project, multiple thin coats is the secret.

IMG_7821

IMG_7809

We hammered in four felt-bottomed furniture sliders as the final step and our project was done!

IMG_7834

Behold, the DIY knockoff Nelson Platform Bench:

Img 2 800px

IMG_7842

IMG_7865-Edit

IMG_7945

IMG_8045

IMG_7925

-Becki and Chris @ The Uncommon Common Law

—————————————————————————————————————————————————————–

You would never guess from looking at their DIY Nelson Bench Knock Off that it only cost $136.52! If you think their bench is awesome, then you will want to check out their rock star bedroom makeover and the rest of their blog…

Before-After

They really know how to add style to an empty room, huh?!

CWTS LOGO 2014 Sponsors Final

Did you know East Coast Creative’s Most Popular Blog Project of all time is now for sale?!?

Get Ready to Break Up with Your Bedtime Routine!

Check out our online store!

Game of Love

The comments +

  1. Beth H says:

    Wow. Absolutely beautiful job. I’ve done a slat bench from African teak, but it didn’t have the slots like you did on this one. I love it! Thanks for the tutorial!

  2. […] week of Knock Off projects from Creating with the Stars (check out the top three here, here, and here), and now we have one more for you from the link up party! We’re so grateful for all of the […]

  3. […] As the top three, Becki and Chris put together a tutorial for us, check out the details of their beautiful DIY Nelson Bench here. […]

  4. […] Round 1: Knock Off We had to create a knock off of a product. We chose to create a replica of the iconic Herman Miller Nelson Bench. We placed 3rd out of 12 in this round. Tutorial here. […]

  5. […] and Chris of The Uncommon Common Law were this year’s winner of Creating with the Stars at East Coast Creative. And looking at this stunning bench they made, it’s not too hard to see why! The couple recreated […]

  6. designdreamer says:

    WOW!!!
    That is awesome!

  7. […] This knockoff Nelson bench popped up in blogland a few months back, and I am obsessed with it. I don’t have the talent for it yet… but I will.  […]

  8. dampfen says:

    Hello! I’ve been reading your weblog for a long time now and
    finally got the bravery to go ahead and give you a shout
    out from Kingwood Texas! Just wanted to mention keep up the great job!

Leave a Reply to Knock Off Link Up Party Winner: West Elm Tripod Lamp - East Coast Creative Blog Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Make a Kid's Mud Kitchen and Produce Stand

DIY PROJECT

Work From Home Corner Office Makeover

VIDEO MAKEOVER

Yard Game Ideas ASO Live! with Kelly + Ryan

DIY IDEAS ON TV

Today Show Nursery Makeover

MAKEOVER

Outdoor Living Space Makeover : Home Becomes

VIDEO MAKEOVER

Must Reads

Get updated on what we're working on

Follow along!